ROTARY DRILL RIG MOUNTED ON INTERNATIONAL S LINE TRUCK + ASSOCIATED DRILLING E

Overig

ROTARY DRILL RIG MOUNTED ON

INTERNATIONAL S LINE TRUCK + ASSOCIATED DRILLING E

1234

Gebruikt

sale-ehub3579

Rotary Drill Rig Mounted on International S Line Truck + Associated Drilling Equipment ($168,000 ex GST) (sale-ehub3579) Drill Rig Type: Rotary Table - Heavy Duty Mast - Retractable Mayhew 2000 Turntable - Water Injection Pump - Onboard Elgi 800 CFM / 250 PSI Rotary Screw Air Compressor - 19x 3.5" Inch x 2 3/8" Inch IF Drill Rods - Driven from Truck Engine through Mayhew Transfer Case - Has been extensively overhauled + mast painted Onboard Air Compressor Make: Elgi Hours: 900 Engine: Deutz BF 6M 1015 C @ 261 kW 800 CFM 250 PSI Truck Make: International Model: S Line Engine: International DT 466 Gearbox: 13 Speed Road Ranger Associated Drilling Equipment - Drill Rods; 15x 6 Metre 3.5" Inch / 4x 6.1 Metre 3.5" Inch / 1x 3 Metre 3.5" Inch / 5x 6 Metre 4.5" Inch - 2 only long winch ropes and heavy duty travelling block - Thread adaptor subs 8 of various sizes to suit equipment being used - 1x Mayhew x 2 3/8“ Inch Male x Male, Rethreaded Kelly Starter Pin - 5x Only Stabilizers; 6” Inch, 7 3/8” Inch, 8 “ Inch, 10 “ Inch & 12" Inch - 1x 12 “ Rock Roller Hole Opener - 1x 14 “ Claw Type Hole Opener - Various Drag Bits: 11 ¾” Inch, 10 5/8” Inch, 10” Inch, 8 ½” Inch, 8" Inch & 7 ¾" Inch - 5x Drag Bits Used; 7 3/8" Inch, 2 at 4 ½“ Inch & 1 at 5 ½“ Inch - Hole Starter Bits; 1x at 9 ½” Inch & 1x at 10" Inch - 2x Claw Bits; 1x 6” Inch & 1x 7 ½“ Inch with replaceable picks - 15x New Tungsten Picks for claw bits - Current 6” Inch Down Hole Hammer - 1x 1.5 meter long Hammer Collar - Air Bleed Off Sub for Top of Hammer - 1x 8“ Inch Hammer Bit for current 6" Inch Hammer - 3x Current Hammer Bits 7.5“ Inch used - 6x Used 7 ½” Inch Hammer Bits to suit current 6“ Inch Hammer (about 7" Inch now) - 5“ Inch Hammer with 3 bits - 6“ Inch Mission Hammer (used) - Several bits for Mission Hammer; 2x good 7“ Inch Bits and 9x used 7“ Inch Bits - 4“ Inch Halco Hammer and 2x Bits - 5x only Skillet Plates for turn table to suit various drill rods and thread adaptor subs - 3 ½“ Inch Heavy Duty Spanner to hold stabilizers etc. and a 3 ½“ Inch holder device - 1x Lifting Plug with Air Inlet - 1x 1 ½“ Inch Hose for lifting plug about 10–12 metres long - Big Hammer breakout vice on stand - 2x only Bit Breakout Spanners for Hammer - 1x only 48” Inch Rigid Stilsons - 1x only 48“ Inch Heavy Duty Chain Tongs - 2x only 30” Inch Chain Tongs - 1x only 18” Inch Aluminum Stilsons - 1x only 12” Inch Aluminum Stilsons - 1x only 36" Inch Stilsons - Various clamps for casing lifting and holding - A number of second hand rig parts (Everything that is there) Truck Mounted Rotary Drill Rig Location: Queensland, Australia